Dolphin has supported the recalibration shortcut (X+Y+Start) for quite a long while. So if someont's axises are terrible, you could easily
recalibrate.
Games even get the initial calibration upon boot(Most of the time).
While changing over the GCAdapter code, I was testing to make sure the reset and calibration shortcuts still worked, turns out they didn't work at
all.
Looking in to the problem, we capture the combination properly, and we wait three seconds until we actually fire that off recalibration.
The problem is for Nintendo's SDK to properly handle recalibrating, we need to send back data saying that it needs to recalibrate.
On hardware this is done as part of the 64bits of data the controller sends back to us.
On holding of the controller, bit 61 of the return value is set, which the Nintendo SDK catches, and then signals immediately afterwards a CMD_ORIGIN
command in order to recalibrate the controller.
We were outright ignoring this bit, so the library wasn't ever recalibrating. I suspect in the past the class itself used to use the calibration data
to to offset the data, but somewhere along the lines it got munged out of existence.
The Gamecube adapter does this shortcut in a bit of a unique way, instead of sending the command and having the library support it and what have you.
Once holding the shortcut for the amount of time, the adapter reports back that the controller has actually been disconnected. Then when you let go of
the combination, the adapter states that a new device has been connected to that port, and the recalibration happens because a new device is
"connected."
This fixes controller calibration for both emulated GC controllers and also the Wii Gamecube Adapter.
We don't throttle by frames, we throttle by coretiming speed.
So looking up VI for calculating the speed was just very wrong.
The new ini option is a float, 1.0f for fullspeed.
In the GUI, percentual values are used.
The Wii U Gamecube controller adapter setup has always been a bit weird. It tries to be as automatic as possible to make the user experience as easy
as possible.
The problem with this approach is that it brings a large disconnect in the user experience because you have the Gamecube controller setup with regular
gamepads and then for some reason below that you have a "direct connect" option which will cause the Gamecube Adapter to overwrite the regular inputs
if something was connected.
While this works and allows the user to only click one checkbox to get the device working, it breaks the user's experience because they don't really
know what "direct connect" means and won't look it up to figure out what it is. Just expecting the device to work (At least one occurence of this in
the IRC channel in the last week).
This way around also had the terrible nature of making the code more filthy than it needed to be. The GCAdapter namespace was parasitic and hooked in
to the regular GC Controller SI class to overwrite the data that it was getting from the default configuration.
Now instead we have a specific SIDevice class for the Wii U Gamecube adapter. This class is fairly simple and is a child of the regular SI Gamecube
Pad device and only reimplements what it needs to.
This also gives the ability to configure controllers individually, which allows the user to configure rumble individually per pad input.
Overall the code is cleaner, and it fits more in line with how the rest of Dolphin works.
Replaces them with forward declarations of used types, or removes them entirely if they aren't used at all. This also replaces certain Common headers with less inclusive ones (in terms of definitions they pull in).
I'm not sure if Maker is the best name (Developer? Publisher?
Company? Copyright?) but I went with it because it's
what the game properties window uses. For the sake of
backwards compatibility, the INI option wasn't renamed.
When enabled, the silent option will avoid popping up dialog boxes for
overwrite confirmation or codec selection. The codec selection defaults to
uncompressed RGB.
This is required for FifoCI on Windows which needs to drive Dolphin from the
command line exclusively.
Won't work with all games, but provides a nice way to spend extra CPU to make
a variable framerate game faster (e.g. Spyro or The Last Story), or to make
a game use less CPU at the cost of a lower framerate (e.g. Rogue Leader).
The libusb driver must be installed on the adapter (e.g. zadig can be used to install the driver in Windows). GameCube pad controllers are supported and will override the current input device assigned to the port. GameCube controller buttons are auto-configured and cannot be re-assigned. Rumble is supported. Hotplug is supported while playing a game. If a controller is unplugged from the adapter, Dolphin will fallback to using the host input device on that port. If a port on the adapter is unused, Dolphin will use the host input device for that port, allowing a mixture of host input devices and controllers connected to the adapter.
The adapter support can be disabled in the Controllers config if the OS driver is preferred (allowing the pad buttons to be reconfigured).
One adapter per system is supported.
* Added country flags for games from Netherlands and Spain
* Added separate category for Region Free games (Uses European flag as placeholder)
* Added missing country filter options in "show regions" menu
* Rearranged country filters for readability
* Incremented CACHE_REVISION
Also fixed various country filters not showing up as options in the "Show regions" menu.
This will allow us to simplify the checks for background input and push
them further down into the architecture, into the ControllerEmu layer.
The new setting isn't actually used yet, though.
This breaks Linux stdout logging.
This reverts commit 7ac5b1f2f8, reversing
changes made to 9bc14012fc.
Revert "Merge pull request #77 from lioncash/remove-console"
This reverts commit 9bc14012fc, reversing
changes made to b18a33377d.
Conflicts:
Source/Core/Common/LogManager.cpp
Source/Core/DolphinWX/Frame.cpp
Source/Core/DolphinWX/FrameAui.cpp
Source/Core/DolphinWX/LogConfigWindow.cpp
Source/Core/DolphinWX/LogWindow.cpp
